Why Doesn’t My Motar 3 Coil Glow Red? A Complete Guide for Longmada Users

Why Doesn’t My Motar 3 Coil Glow Red? A Complete Guide for Longmada Users

Discover the Longmada Crystal Vape Kit: Pure Flavor, Smooth Clouds, and Water Filtration Reading Why Doesn’t My Motar 3 Coil Glow Red? A Complete Guide for Longmada Users 5 minutes

If you are new to the Longmada Motar 3 Wax Vape Kit, you may sometimes wonder:

“Why is my Motar 3 coil not glowing red when I press the button?”

The good news is: this doesn’t always mean something is wrong. The Motar 3 coil uses an advanced ceramic + quartz heating system, and sometimes the heat is there even if you don’t see the red glow.

The best way to figure out what’s happening is to look at the battery indicator lights. These signals will tell you exactly why the coil is not heating or glowing and how you can fix it.


🔋 Battery Indicator Lights Explained

When the Motar 3 coil doesn’t glow and the indicator light flashes then goes out, here’s what it means:

1. 🔴 Red Light Flashes 5 Times → Low Battery

  • Cause: Battery doesn’t have enough power.

  • Solution: Recharge your Motar 3 battery. Low battery prevents the coil from reaching proper temperature.


2. ⚪ White Light Flashes 3 Times → Connection Issue

  • Cause: The coil is not connected correctly to the base or battery.

  • Solution:
    a) Reinstall the coil — always attach the coil to the base first, then connect to the battery.
    b) Replace the coil if it is old or damaged.

  • Youtube video-White Light Flashes 3 Times

3. Mode Light Flashes Twice → Device Shuts Down (Short Circuit)

  • Cause: A short between the coil, base, or battery thread.

  • Solution:
    a) Inspect the coil, base, and battery pin for debris or residue. Clean thoroughly.
    b) Replace the heating coil if damaged. Recharge the battery, reactivate, and press the power button 5 times to restart.


4. 🔴🟢 Red & Green Lights Flash Twice → Overheat Protection

  • Cause: Device has been heating continuously for 3 minutes and shuts down for safety.

  • Solution: Wait 3 minutes before using again.


5. 🔴⚪ Red & White Lights Flash 3 Times → Mode Not Set Properly

  • Cause: Incorrect gear or temperature setting.

  • Solution: Press the button 3 times quickly to adjust the mode, then vape again.


6. ⚫ No Light When Pressing the Button → Auto Shut-Off

  • Cause: Device was idle for more than 5 minutes.

  • Solution:

    a)Press the button 5 times to power on.

    b)Recharge the battery, reactivate, and press the power button 5 times to restart.


💡 What If the Coil Light Is On but Still Doesn’t Glow Red?

Sometimes the Motar 3 coil is working perfectly, but you don’t see the coil glowing red. This is actually normal:

  1. Ceramic Plate Placement – The ceramic heating plate sits tightly against the quartz cup, so the red glow may be hidden.

  2. Bright Environment – In a well-lit room, the faint red glow may not be visible.

The coil is still reaching the correct temperature even if you don’t see it glow.

 


🌡️ How to Test If the Coil Is Heating Properly

Not sure if your coil is hot enough? Try these two simple methods:

  1. Use a Temperature Tester – Place a digital temperature probe or infrared gun at the center of the quartz bowl.

  2. Water Drop Test – Add a small drop of water into the heating bowl. If the water  boils or evaporates quickly, the coil is heating normally.


📺 Video Support

Need a visual guide? Watch our official YouTube tutorial to learn how to check your Motar 3 coil and battery step by step:
👉 YouTube Video – Why the Motar 3 Coil Doesn’t Glow Red

If replacing the coil still does not solve the issue with your Motar 3, please watch our YouTube video guide to check whether the problem is with the battery or the atomizer:

How to Check If Your Motar3 Battery Is Faulty – Simple Tweezer Test!


✅ Pro Tips to Extend Coil Life

  • Always use 20–25W power. High wattage can burn out coils.

  • Use manual mode: press only when inhaling, release when not. This reduces stress on the coil.

  • Never touch the heating chamber with sharp or hard tools.

  • Wait for the coil to cool completely before cleaning.

  • Avoid dropping the atomizer — the quartz/glass can break.

  • Keep extra replacement coils handy for uninterrupted vaping.


🔑 Conclusion

If your Motar 3 coil is not glowing red, don’t panic. In most cases, the coil is still heating correctly — the design of the ceramic and quartz system simply hides the glow. The battery indicator lights are your best guide to understanding what’s happening.

By learning these signals and following the troubleshooting steps above, you can easily solve most issues and keep your Longmada Motar 3 Wax Vape Kit running smoothly.

Enjoy powerful, flavorful clouds — without worrying about whether your coil glows red.

Leave a comment

This site is protected by hCaptcha and the hCaptcha Privacy Policy and Terms of Service apply.